Fluke 2052 Advanced Wire Tracer Kit

  • Fluke 2052 Advanced Wire Tracer Kit
  • Fluke 2052 Advanced Wire Tracer Kit
  • Fluke 2052 Advanced Wire Tracer Kit
  • Fluke 2052 Advanced Wire Tracer Kit
  • Fluke 2052 Advanced Wire Tracer Kit


  • Locate energized and de-energized wires quickly and accurately in walls, ceilings, and floors
  • Find breaks or opens and shorts, and identify breakers and fuses easily
  • CAT IV 600 V safety rated
  • Includes the i400 AC Current Clamp accessory for inducing a tracing signal on the cable when there is no access to bare conductors

Produktoversigt: Fluke 2052 Advanced Wire Tracer Kit

Built to Keep You Safe

The Fluke 2052 Advanced Wire Tracer accurately and safely troubleshoots energized and de-energized wires in residential, commercial, and industrial environments up to CAT IV 600 V. This CAT rating offers the highest protection available on any wire tracer. It’s designed to protect you from the most dangerous levels of transient overvoltage, spikes up to 8,000 V, that can occur in industrial and utility environments. This is especially important for scenarios you may encounter in environments like industrial plants, factories, and hospitals where critical equipment cannot be taken offline.

Wire Tracing Customized for Your Application

Whether troubleshooting electrical wiring and equipment in residential homes, commercial buildings, or high-voltage utility plants, the Fluke 2052 can find breaks or opens and shorts. Its different modes and functions give you the flexibility to troubleshoot a wide range of electrical wiring and circuitry problems you may encounter on the job.

Four Receiver Tracing Modes

The 2052-R Receiver detects the signal in wires and cables using two methods: passive tracing without the transmitter for non-contact voltage detection and active tracing with the transmitter for all other modes. The receiver’s tip sensor can trace wires in corners, tight spaces, and junction boxes.

  • “Quick Scan” mode for energized wire detection and visualization on the large color LCD
  • “Precision” mode for more precise detection of a wire
  • “Breaker” mode for easy breaker and fuse identification based on the highest recorded signal detected from the transmitter
  • “Non-Contact Voltage Detection” mode to trace energized wires without the use of the transmitter

Three Transmitter Power Modes

The 2000-T Transmitter works on energized and de-energized circuits up to CAT IV 600 V and features high, low, and loop modes. These modes change the strength of the induced signal and can help provide more accurate results, depending on the circuit you’re tracing.

  • “High” mode for normal energized and de-energized circuits
  • “Low” mode for precision tracing with a low signal to reduce coupling to nearby wires and metal objects
  • “Loop” mode for closed loop de-energized circuits

Two Transmitter Output Frequencies

The 2000-T automatically senses whether the system is energized or de-energized and selects a 6 kHz or 33 kHz output frequency.

Eight Receiver Sensitivity Levels

More sensitivity levels mean more flexibility and accuracy when tracing.

Complete Kit

The Fluke 2052 Advanced Wire Tracer Kit conveniently comes with everything required to start tracing wires and circuits. The accessory kit includes test leads, test probes, blade and round outlet adapters, and alligator clips to connect the transmitter to electrical systems. Connecting the transmitter to a bare conductor with the included alligator clips and test leads will always provide the most accurate results. However, in situations where a direct connection to a bare conductor is not available, the included i400 Current Clamp can be used with the “Loop” mode to induce a boosted 6 kHz signal through the insulation. The kit also includes batteries and a hard carrying case.


Specifikationer: Fluke 2052 Advanced Wire Tracer Kit

General2052R Receiver2000T Transmitteri400 AC Current Clamp
Measurement categoryCAT IV 600 VCAT IV 600 VCAT IV 600 V, CAT III 1000 V
Operating voltage600 V AC/DC600 V AC/DC1000 V AC
Operating frequencyEnergized: 6.25 kHz
De-Energized: 32.768 kHz
Energized/Loop: 6.25 kHz
De-Energized: 32.768 kHz
Signal indicationsNumeric, bar graph display and audible beepLEDs and audible beepN/A
Response timeTip Sensor (Energized/De-Energized): 500 ms
NCV: 500 ms
Battery monitoring: 5 s
Line voltage monitoring: 1 s
Battery voltage monitoring: 5 s
Current output of signal (typical)N/AEnergized circuit:
High mode: 60 mA rms
Low mode: 30 mA rms

De-energized circuit:
High mode: 110 mA rms
Low mode: 40 mA rms
Loop mode with test leads: 160 mA rms
Loop mode with i400 AC Current Clamp:
385 mA rms
Signal voltage output (nominal)N/AEnergized circuit:
High mode: 14 W @ 230 V ac/50 Hz,
3.33 kΩ @ 230 V ac
Low mode: 4.6 W @ 230 V ac/50 Hz,
11.5 kΩ @ 230 V ac

De-energized circuit:
High mode: 31 V RMS, 140 Vp-p,
0.86 W @ 1 kΩ load
Low mode: 27.5 V RMS, 120 Vp-p,
0.1 W @ 1 kΩ load
Loop mode with test leads: 32 V RMS,
140 Vp-p, 0.87 W @ 1 kΩ load
Loop mode with i400 AC Current Clamp:
31 mV, 0.89 W @ 1 Ω load
Range detection (open air)Tip Sensor: Energized
Max distance via air: up to 6.1 m (20 ft)
Pinpointing: approx. 5 cm (1.97 in)

Tip Sensor: De-Energized
Max distance via air: up to 4.5 m (14.7 ft)
Pinpointing: approx. 5 cm (1.97 in)

NCV (40 Hz to 400 Hz)
Max. sensitivity: 90 V up to 2 m
Min. sensitivity: 600 V up to 1 cm
Current rangeN/AN/A400 A
Basic accuracyN/AN/A2 % + 0.06 A
(45 Hz to 400 Hz)
Display sizeLCD 63 mm (2.5 in)LEDsN/A
Display dimensions (W x H)37 mm x 49 mm (1.45 x 1.93 in)N/AN/A
Display Resolution240 px x 320 pxN/AN/A
Display typeTFT LCDLEDsN/A
Display color16-bitOperating mode LEDs: red
Battery status LEDs: green, yellow, red
Operating temperature-20 °C to 50 °C (-4 °F to 122 °F)-20 °C to 50 °C (-4 °F to 122 °F)-20 °C to 50 °C (-4 °F to 122 °F)
Operating humidity45%: -20 °C to <10 °C or 40 °C to 50 °C
(-4 °F to <50 °F or 104 °F to 122 °F)
95% (non-condensing): 10 °C to <30 °C
(50 °F to 86 °F)
75%: 30 °C to <40 °C (86 °F to <104 °F)
45%: -20 °C to <10 °C or 40 °C to 50 °C
(-4 °F to <50 °F or 104 °F to 122 °F)
95% (non-condensing): 10 °C to <30 °C
(50 °F to 86 °F)
75%: 30 °C to <40 °C (86 °F to <104 °F)
10 °C to <30 °C
(95 %: 50 °F to <86 °F)
30 °C to <40 °C
(75 %: 86 °F to <104 °F)
40 °C to <50 °C
(45 %: 104 °F to <122 °F)
Operating altitude2000 m (6561 ft)2000 m (6561 ft)2000 m (6561 ft)
Transient protectionN/A N/A
Pollution degree222
IP ratingIP 40IP 40IP 40
Drop test1 m (3.28 ft)1 m (3.28 ft)1 m (3.28 ft)
Power supply4 x AA (alkaline)8 x AA (alkaline)N/A
Power consumption (typical)110 mAHigh/low mode: 70 mA
Loop mode with Clamp: 90 mA
Consumption without signal
transmission: 10 mA
Battery lifeApprox. 16 hHigh/low mode: approx. 25 h
Loop mode: approx. 18 h
Low battery indicationYesYesN/A
FuseN/A1.6 A, 700 V, fast-acting,
Ø 6 x 32 mm, 50 kA interrupt
Maximum conductor sizeN/AN/A32 mm (1.26 in)
Dimensions (L x W x H)Approx. 183 x 75 x 43 mm
(7.2 x 2.95 x 1.69 in)
Approx. 183 x 93 x 50 mm
(7.2 x 3.66 x 1.97 in)
Approx. 150 x 70 x 30 mm
(5.9 x 2.75 x 1.18 in)
WeightApprox. 0.27 kg (0.6 lb)Approx. 0.57 kg (1.25 lb)Approx. 0.114 kg (0.25 lb)
Mechanical2000ACC Test Lead Accessory Kit
Includes2x 1 m test leads (red, black),
1x 7 m test lead (green),
2x test probes (black),
2x alligator clips (red, black),
2x outlet blade adapters (red, black),
2x outlet round adapters (red, black)
Measurement categoryCAT IV 600 V (test leads), CAT II 1000 V (test probes), CAT IV 600 V (alligator clips),
CAT II 300 V (outlet adapters)
Operating voltage and current600 V, 10 A max. (red/black leads), 600 V, 10 A max. (green lead), 1000 V, 8 A max. (black probe)
600 V, 10 A max. (alligator clips), 300 V, 10 A max. (outlet adapters)
Operating temperature0 °C to 50 °C (32 °F to 122 °F)
Operating humidity10 °C to <30 °C (95 %: 50 °F to <86 °F), 30 °C to <40 °C (75 %: 86 °F to <104 °F),
40 °C to <50 °C (45 %: 104 °F to <122 °F)
Storage temperature and humidity0 °C to 60 °C (32 °F to 140 °F),
Operating altitude2000 m (6561 ft)
Pollution degree2
Water and dust resistanceIP 20
Drop proof1 m (3.28 ft)
DimensionsRed/black leads: 1 m (3.28 ft), Green lead: 7 m (22.97 ft), Alligator clips: approx. 95 x 45 x 24 mm (3.74 x 1.77 x 0.94 in),
Outlet adapters: 72 x 18 x 18 mm (2.83 x 0.71 x 0.71 in)
WeightApprox. 0.4 kg (0.88 lb)