TITLE | USE WITH |
6003A | All |
The updating of embedded software should only be performed after given specific instructions to do so from Technical Support or a Fluke Calibration Authorized Service Center. If the update isn't performed properly, your product may be inoperable until it is. | |
Instructions to update by USB | |
Installation Put the CD into the computer, wait for autorun and select “Software installation” and “Uploader” or start direct “install\freeware\uploader”. Uninstall Uploader To remove the Uploader software from your system, you should run “uninstall” from “Programs” ("Start -> Programs -> Uploader -> Uninstall Uploader" from the Windows Start menu). Uploading Firmware 1. Connect the calibrator to the computer using an RS232 cable. 2. Select RS232 in the instrument menu as the active interface and set the baud rate to 9600 Bd. 3. Start the Uploader “Start->Program files->Uploader->Uploader.exe”. The following screen will appear: ![]() 4. Select computers port (COM1 … COM32) and the source file. The source file is a data file that contains the new firmware with the extension “.upl”. 5. Press “Connect”. The following screen will appear: ![]() 6. It is recommended to keep the transfer speed as-is and press “Upload” (in the case of an unsuccessful upload, reduce the transfer speed and try again). The following screen will appear: ![]() 7. Uploader automatically reloads all internal programs step by step. 8. After successful upload, the Uploader displays the following: ![]() Problems While Uploading New Firmware In the case that the upload does not finish properly (power supply disconnection, failed communication, etc.) the instrument will no longer contain internal software. Switch the instrument’s power supply off, wait approximately 10 seconds, and switch it on again. The instrument will display the message “Internal SW damaged!”. Repeat the procedure upload. The instrument is switched to RS232, 9600Bd mode automatically. | |
Updates Include: | |
Version 1.048 (2019 Oct. 25) Fix: Bug fixed that caused the GUI to lock up when too many characters were entered into the calibration password field. |
Lihat merek Fluke lainnya
-
Produk
-
- Fitur Unggulan
- Aksesoris
- Alat untuk infrastruktur bangunan
-
Alat tes elektrikal
- Multimeter digital
- Alat Basic tester
- Clamp meter
- Kualitas daya
- Alat ukur Earth ground
- Alat Installation tester
- Alat berisolasi
- Alat ukur standar intrinsically safe
- Alat analisis baterai
- Alat Insulation tester
- Alat Portable oscilloscope
- Alat Portable appliance tester
- Alat untuk industry solar
- Tester nirkabel
- Pencitraan termal dan akustik
- Pengukuran suhu
- Tester kabel jaringan
- Alat penyelarasan
- Alat kalibrasi
- Perangkat lunak Fluke
-
- Pelajari
- Dukungan
- Produk
- 5 Fitur Unggulan
- 2 Aksesoris
- 4 Alat untuk infrastruktur bangunan
- 14 Alat tes elektrikal
- 3 Pencitraan termal dan akustik
- 2 Pengukuran suhu
- 2 Tester kabel jaringan
- 1 Alat penyelarasan
- 9 Alat kalibrasi
- 2 Perangkat lunak Fluke
- Alat untuk infrastruktur bangunan
- Alat untuk bidang HVAC
- Alat tes indoor air quality
- Alat laser distance meter
- Alat laser level
- Alat tes elektrikal
- Multimeter digital
- Alat Basic tester
- Clamp meter
- Kualitas daya
- Alat ukur Earth ground
- Alat Installation tester
- Alat berisolasi
- Alat ukur standar intrinsically safe
- Alat analisis baterai
- Alat Insulation tester
- Alat Portable oscilloscope
- Alat Portable appliance tester
- Alat untuk industry solar
- Tester nirkabel
- Alat kalibrasi
- Kalibrator Proses
- Kalibrasi listrik
- Kalibrasi RF
- Akuisisi data dan tes umum
- Kalibrasi Suhu
- Kalibrasi kelembapan
- Kalibrasi Tekanan
- Kalibrasi aliran
- Software Fluke Calibration
- Pelajari
- 5 Fluke Resource Center
- Program Kemitraan Edukasi Fluke
- Pameran dagang dan seminar
- Webinar
- 8 Alat dan kalkulator
- Alat dan kalkulator
- Kalkulator kebocoran udara | ROI
- Bidang pandang kalkulator
- ii-Series reporting tool
- PT100 calculator
- FCAL PT100 table generator
- Downtime cost calculator
- Thermocouple voltage to temperature calculator
- Thermocouple table voltage calculator
- Layanan Pelanggan
- Hubungi Kami
- Layanan Kalibrasi
- Perbaikan
- Lokasi Pusat Servis
- Kualitas dan Akreditasi
- MET/SUPPORT
- Sumber daya produk
- Dasar pengetahuan
- Manual
- Registrasi Produk
- Peringatan Keselamatan
- Unduh pembaruan perangkat lunak
- Garansi
- Material safety data sheets (MSDS)