All HVAC articles
Troubleshooting common PV system problems
With the push to energy independence and renewable energy sources, HVAC technicians need to know how to troubleshoot photovoltaic systems
Energy logging in a building's ventilation system
A big savings point is the efficiency of the equipment used to run your HVAC system—the motors, chillers, boilers, etc.
How harmonics impact equipment
Harmonics-Understanding, measuring, and interpreting results.From minor control trips to compressor and transformer failures, harmonics can impact every type of HVAC equipment
Fundamental IAQ/HVAC measurements with the Fluke 975 AirMeter™
The 975 gathers ten fundamental IAQ parameters: Temperature, Humidity, Dew Point Temperature, Web Bulb Temperature, Carbon Dioxide, Carbon Monoxide, Air Velocity, Air Volume, and Percentage of Outdoor Air (calculated from temperature or CO2). This application note reviews those parameters and the associated functions on the 975. For more detailed information, see other app notes from the Fluke HVAC/IAQ library.
Detecting carbon monoxide
Why, where, and how to detect carbon monoxide (CO) using a simple tool (Fluke CO-220 Carbon Monoxide Meter)
Boiler maintenance and troubleshooting best practices
Boilers and their associated systems are an important part of a modern commercial building's central energy plant. Prevent costly downtime and expensive equipment failures.
Meeting Critical Cooling Requirements
In a chiller plant, meeting critical cooling requirements with the Fluke 830 Laser Shaft Alignment Tool: cooling towers, pumps, piping, shaft alignment.
True RMS tools for energy efficient HVAC systems
HVAC technology true-RMS meters are essential test tools for accurately measuring and troubleshooting complex HVAC control systems.
The art of automation and energy efficiency
Using Fluke tools for energy efficiency and cost savings. How the Figge Art Museum automated their HVAC control systems, reduced energy consumption and saved on annual energy costs
Insulation resistance and electrical testing for HVAC compressor motors
HVACR mechanics rarely rely on a single test to pass or fail a function or process. As they walk up to a condensing unit, they listen, they wave their hand over the condenser discharge air, and then they grab the suction line, the liquid line, and the discharge line (and wish they hadn't done that). All of this before they even open their tool box.
Diagnosing mold problems
One of the possible problems in facilities today is the presence and effects of mold on the indoor environment. Molds are normally present in nature. They reproduce by means of tiny spores that float through the air and are invisible to the naked eye. They can grow on wood, paper, carpet, foods, and insulation - but none of the many types of mold will grow without water or moisture. When excessive moisture accumulates in buildings or on building materials, mold growth will often occur, particularly if the moisture problem remains unaddressed.
Evaluating relative humidity: Key factors and measurements
Understanding the relationship between dry bulb temperature, wet bulb temperature, relative humidity, and dew point temperature is essential in all facets of air conditioning. These psychrometric processes play an especially important role in building and materials integrity, occupant health and comfort, and overall indoor air quality.
Using Fluke Air Particle Counters in Healthcare Facilities
Learn how using Fluke airborne particle counters in healthcare facilities helps meet IAQ standards and contamination testing.
Leading facility solutions firm upgrades popular instrument with Fluke Connect model
MacDonald-Miller standardized on the Fluke 902 Clamp Meter when it came out several years ago.
Tune up your cooling system now!
When the weather is warm outside, it's imperative to make sure that your building's mechanical cooling systems are working at maximum efficiency.
My chiller plant is down, do you know how incredibly critical it is?
If chilled water flow is interrupted for even a few minutes the IT server room might overheat and critical computer services could go down. Another vital area is a hospital operating room. In a plant, essential machinery uses chilled water for process cooling. While many plants have excess capacity, much of this capacity is not available at high ambient temperature and high humidity conditions.
Troubleshooting web-based HVAC control system networks
Scenarios showing how to prevent system failures and downtime caused by HVAC network problems.
Measuring air velocity with the Fluke 975 AirMeter™: Using the Velocity Probe
Air velocity is a key parameter in evaluating airflow system performance. As part of basic testing, adjusting and balancing of HVAC air distribution systems, most HVAC technicians now use an anemometer to measure air velocity at grilles-registers-diffusers, within a duct, or in open spaces.
When start-up inspections pay off for HVAC
After years of being a serviceman - slinging ladders, dragging tools across attics and through crawlspaces, standing in all sorts of weather on rooftops - I can now leave the service work to one of the younger techs with better knees and concentrate on my primary job as company start-up man.
A Slippery Slope? Not for Curling's Ice Technologists
Preparing ice for curling competitions with the aid of Fluke infrared camera, infrared thermometer, digital thermometer, and temperature humidity meter
Improve your team productivity when working on variable air volume (VAV) systems
In my role as a consultant and trainer, I spend a lot of time working with facility maintenance personnel. Recently I was recently given a formidable task by the maintenance leadership of the plant services shop of a large university.
Duct traversal airflow measurement
This how-to guide explains why and how to conduct a duct traverse, how to insert the measuring device and a step-by-step process of taking the measurements. Tips and additional resources are included.
Battling high humidity levels in comfort cooling systems
Most of the hours when comfort cooling systems operate are well below outdoor design conditions. The equipment may have been selected to maintain 75°F and 50% RH indoors when it is 95°F outdoors, but what happens at lower outdoor temperatures? There's less run time to satisfy the thermostat, but not enough run time to maintain desirable or comfortable humidity levels. Some modern equipment and components are designed to overcome this effect.
Determining air quality impacts
Testing and comparing air quality in two homes for ventilation system effectiveness, using a Fluke 985 Particle Counter: particulates, formaldehyde, other VOCs
Tech Tips - How Much Energy Does That High-Efficiency Chiller Waste?
Five years ago, with the move to highefficiency equipment, Fluke began receiving trouble calls from service techs. The calls came post-installation, and they weren't about the new equipment—they were about other parts of the system that were now operating erratically, if at all.
Electronics in your building don't like power problems
As we have seen, power problems have a bad effect on electronic devices. To detect a power problem, a technician will first check out the power supply to a device to make sure it is functioning properly.
HVAC and industrial applications for the Fluke T+ and T+Pro Electrical Testers
If you're still using these solenoid testers, it's time to trade up to an solid-state electrical tester.