Fluke Networks CableIQ™ Qualification Tester
Fluke Networks CableIQ™ Qualification Tester is rated out of 5 by 3.
Copper qualification tester troubleshoots and qualifies Ethernet network cabling speed (10/100/1000/VoIP)
- Works on live networks to provide Ethernet switch detection and device configuration
- Measure network capacity (10 Meg, 100 Meg, 1 Gig) to determine support for VoIP, data and video
Product overview: Fluke Networks CableIQ™ Qualification Tester
CableIQ finds common cable faults and data rate. Cables often fail in harsh industrial environments where cables are exposed to vibration, extreme flexing, moisture, expansion and contraction from temperature change. Failures result in costly production downtime so it’s important to quickly identify where the cable is broken so it can be replaced or repaired. CableIQ checks continuity on all wires displays results graphically so you can see opens, shorts, and cross wires and reports the distance to an open connection within the cable. It also checks if the cable can support data rates.
Troubleshoot and qualify Ethernet network cabling speed
- Advanced troubleshooting diagnostics; insertion loss, cross talk, noise issues
- Core troubleshooting features; length, distance to fault, graphical wire mapping, opens, shorts, power over Ethernet (POE) detection
- Tests all copper cabling media: twisted-pair, coax, and audio
- Locate and trace cables with digital toning technology. Requires IntelliTone 200 Digital Probe (included with CIQ-KIT)
- Qualifies and troubleshoots Industrial Ethernet cabling
Specifications: Fluke Networks CableIQ™ Qualification Tester
|Cable types supported||UTP, STP, FTP, SSTP, RG6, RG59, audio and security|
|Qualification autotests||1000BASE-T, 100BASE-TX, 10BASE-T, VoIP, 1394b S100, TELCO, Wiremap only, Coax|
|Supported tests||Wiremap, length, cable signal performance, digital toner, analog toner, Ethernet port detection and identification, analog telephone detection, blink port light, continuity, speaker test, cable fault finding, video signal detection.|
|Wiremap||Can detect single wire faults and supports MultiMap mode with up to seven remote office identifiers. Draws proportional wire length to breaks. Detects split pairs.|
|Find fault||Measures crosstalk and impedance and compares against appropriate limits based on qualification test selected. Detects location of large point sources as well as distributed sources in the cabling if they are sufficient to disqualify the application|
|Results storage||Up to 250 qualification test results|
|Power||Battery type: 4 AA (NEDA 15A, IEC LR6) alkaline batteries|
|Battery life||20 hours of typical use, without backlight|
|Other battery types supported||4AA photo lithium, NIHM, NICAD|
|Dimensions and weight||7in x 3.5in x 1.75in (17.8cm x 8.9cm x 4.5cm) 1.2 lb (0.55 kg)|
Does the Fluke Networks CIQ-100 Cable Tester come with a Calibration Certificate?
The CableIQ does not require calibration, so there are no calibration certificates for the CableIQ.
Date published: 2023-05-01
Rated 5 out of 5 by Big Bob 27 from A Simpler Life I used this with the last company I worked with and was terrific! Made wire locating easier, tested every wire for correct patterns and faulty roles. The length reading was always CORRECT! which made some jobs easier.
Date published: 2022-11-24
Rated 1 out of 5 by Tech27485929q from Screen broke on day two. Be extra careful. There is only a thin plastic sheet protecting the screen. The screen broke and now I can't use it. Good quality for junk.
Date published: 2022-07-20
Rated 5 out of 5 by Matt14 from Makes my life easier my company provided one of these for me to use in the field. saves me loads of time.
Date published: 2020-11-19