Fluke 376 FC True-RMS AC/DC Clamp Meter with iFlex
Fluke 376 FC True-RMS Clamp Meter with iFlex is rated out of 5 by 38.
Key features
- Measures AC/DC current with included iFlex current probe
- VFD low pass filter for accurate measurements of non-linear signals
- Remotely log, trend and monitor to pinpoint intermittent faults
- Inrush measurement to filter out noise and capture starting current
Product overview: Fluke 376 FC True-RMS AC/DC Clamp Meter with iFlex
The Fluke 376 FC True-rms Clamp Meter with iFlex is the most advanced troubleshooting tool for industrial and commercial electricians. The 376 is part of the Fluke Connect family of wireless test tools that enable you to log, trend and monitor measurements while remaining safely away from the arc flash zone through Bluetooth connectivity.
Find the cause of difficult problems
The 376 FC clamp meter uses an integrated low-pass filter for accurate measurements of non-linear signals, such as adjustable speed drives, electronic ballasts and other non-linear loads. The clamp also uses proprietary inrush measurement technology to filter out noise and capture motor starting current exactly as the circuit protection sees it.
Measure:
- Voltage to 1000 V AC or DC
- Resistance to 60 kΩ with continuity detection
- Min, max, average, and inrush recording to capture variations automatically
- 500 mV DC measurement range to interface with other accessories
- 1000 μF capacitance measurement
Work safely and conveniently
The 376 FC clamp carries a CAT III 1000 V, CAT IV 600 V safety rating, designed to offer you the highest possible protection in a test tool.
The included iFlex flexible current probe provides easier access to large conductors in tight spaces. The flexible probe:
- Expands the measurement range to 2500 A AC
- Allows frequency measurement to 500 Hz with body jaw and iFlex
Specifications: Fluke 376 FC True-RMS AC/DC Clamp Meter with iFlex
| General Specifications | ||
| AC Current via Jaw | ||
| Range | 999.9 A | |
| Resolution | 0.1 A | |
| Accuracy | 2% ±5 digits (10 Hz to 100 Hz) | |
| 2.5% ±5 digits (100-500 Hz) | ||
| Crest Factor (50 Hz/60 Hz) | 3 @ 500 A | |
| 2.5 @ 600 A | ||
| Add 2% for C.F. >2 | ||
| AC Current via Flexible Current Probe | ||
| Range | 2500 A | |
| Resolution | 0.1 A (≤ 600 A) | |
| 1 A (≤ 2500 A) | ||
| Accuracy | 3% ±5 digits (5 – 500 Hz) | |
| Crest Factor (50/60Hz) | 3.0 at 1100 A | |
| 2.5 at 1400 A | ||
| 1.42 at 2500 A | ||
| Add 2% for C.F. > 2 | ||
| Position Sensitivity | ||
 | ||
| i2500-10 Flex | i2500-18 Flex | |
| A | ||
| Distance from Optimum | 0.5 in (12.7 mm) | 1.4 in (35.6 mm) |
| Error | ±0.5 % | ±0.5 % |
| B | ||
| Distance from Optimum | 0.8 in (20.3 mm) | 2.0 in (50.8 mm) |
| Error | ±1.0 % | ±1.0 % |
| C | ||
| Distance from Optimum | 1.4 in (35.6 mm) | 2.5 in (63.5 mm) |
| Error | ±2.0 % | ±2.0 % |
| Measurement uncertainty assumes centralized primary conductor at optimum position, no external electrical or magnetic field, and within operating temperature range. | ||
| DC Current | ||
| Range | 999.9 A | |
| Resolution | 0.1 A | |
| Accuracy | 2% ±5 digits | |
| AC Voltage | ||
| Range | 1000 V | |
| Resolution | 0.1 V (≤600.0 V) | |
| 1 V (≤1000 V) | ||
| Accuracy | 1% ±5 digits (20 Hz to 500 Hz) | |
| DC Voltage | ||
| Range | 1000 V | |
| Resolution | 0.1 V (≤600.0 V) | |
| 1 V (≤1000 V) | ||
| Accuracy | 1% ±5 digits | |
| mV dc | ||
| Range | 500.0 mV | |
| Resolution | 0.1 mV | |
| Accuracy | 1% ±5 digits | |
| Frequency via Jaw | ||
| Range | 5.0 Hz to 500.0 Hz | |
| Resolution | 0.1 Hz | |
| Accuracy | 0.5% ±5 digits | |
| Trigger level | 5 Hz to 10 Hz, ≥10 A | |
| 10 Hz to 100 Hz, ≥5 A | ||
| 100 Hz to 500 Hz, ≥10 A | ||
| Frequency via Flexible Current Probe | ||
| Range | 5.0 Hz to 500.0 Hz | |
| Resolution | 0.1 Hz | |
| Accuracy | 0.5% ±5 digits | |
| Trigger level | 5 Hz to 20 Hz, ≥25 A | |
| 20 Hz to 100 Hz, ≥20 A | ||
| 100 Hz to 500 Hz, ≥25 A | ||
| Resistance | ||
| Range | 60 kΩ | |
| Resolution | 0.1 Ω (≤600 Ω) | |
| 1 Ω (≤6000 Ω) | ||
| 10 Ω (≤60 kΩ) | ||
| Accuracy | 1% ±5 digits | |
| Capacitance | ||
| Range | 1000 μF | |
| Resolution | 0.1 μF (≤ 100 μF) | |
| 1 μ F (≤ 1000 μF) | ||
| Accuracy | 1% ±4 digits | |
| Mechanical Specifications | ||
| Maximum voltage between any terminal and earth ground | 1000 V | |
| Batteries | 2 AA, NEDA 15A, IEC LR6 | |
| Operating temperature | -10 °C to +50 °C | |
| Storage temperature | -40 °C to +60 °C | |
| Operating humidity - non-condensing (< 10°C) | ≤90% RH (at 10 °C to 30 °C) | |
| ≤75% RH (at 30 °C to 40 °C) | ||
| ≤45% RH (at 40 °C to 50 °C) | ||
| Operating altitude | 2000 m | |
| Storage altitude | 12,000 m | |
| Size (L x W x H) | 249 x 85 x 45 mm | |
| Weight | 395 g | |
| Jaw opening | 34 mm | |
| Flexible current probe diameter | 7.5 mm | |
| Flexible current probe cable length (head to electronics connector) | 1.8 m | |
| Safety | IEC 61010-1, Pollution Degree 2 | |
| IEC 61010-2-032: CAT III 1000 V / CAT IV 600 V | ||
| IEC 61010-2-033:CAT III 1000 V / CAT IV 600 V | ||
| IP rating | IEC 60529: IP30, non-operating | |
| Radio Frequency Certification FCC ID | T68-FBLE IC:6627A-FBLE | |
| Electromagnetic Compatibility (EMC) | ||
| International | IEC 61326-1: Portable, Electromagnetic Environment, IEC 61326-2-2 | |
| CISPR 11: Group 1, Class A | ||
| Group 1: Equipment has intentionally generated and/or uses conductively-coupled radio frequency energy that is necessary for the internal function of the equipment itself. | ||
| Class A: Equipment is suitable for use in all establishments other than domestic and those directly connected to a low-voltage power supply network that supplies buildings used for domestic purpose. There may be potential difficulties in ensuring electromagnetic compatibility in other environments due to conducted and radiated disturbances. Emissions that exceed the levels required by CISPR 11 can occur when the equipment is connected to a test object. | ||
| Korea (KCC) | Class A Equipment (Industrial Broadcasting & Communication Equipment) | |
| Class A: Equipment meets requirements for industrial electromagnetic wave equipment and the seller or user should take notice of it. This equipment is intended for use in business environments and not to be used in homes. | ||
| USA (FCC) | 47 CFR 15 subpart B. This product is considered an exempt device per clause 15.103. | |
| Temperature coefficients | Add 0.1 x specified accuracy for each degree C above 28 °C or below 18 °C | |
Models: Fluke 376 FC True-RMS AC/DC Clamp Meter with iFlex
Fluke 376 FC
Fluke 376 FC True-RMS Clamp Meter
Includes:
- Fluke 376 FC True-RMS Clamp Meter with iFlex
- 18-inch iFlex® Flexible Current Probe
- TPAK magnetic hanging strap
- TL75 Test Leads
- Two AA batteries (Installed)
- Soft carrying case
- Coated instruction card
- Safety information sheet
Reviews: Fluke 376 FC True-RMS AC/DC Clamp Meter with iFlex
Rated 4 out of 5 by HoboFist from Great daily carry meter. But ex-381 owners beware TLDR: Great general purpose meter, will fill just about everything you need for a meter 90% of the time. BUT be leery about coming to this from the older Fluke 381, all the specs are the same...but the wireless functionality is much worse
(Use: Industrial Electrician) I bought this meter to replace my Fluke 381. I had been using the 381 for years as a general multimeter and loved it. It gives you just about everything you need for daily driving it as your carry matter, and having BOTH AC & DC up to 1000 amp on the clamp is a sweet bonus. The one issue I had was that whenever I got a service call to troubleshoot an unknown issue that would have a surprise capacitive circuit(because the customer had no clue). this was an issue because the 381 does not have a capacitance test setting, so I would have to go back out through the facility to get my megger which has the setting in it. Seeing as how this 376FC has the exact reading specifications as the 381, plus the capacitance and mV additions, I figured it was a great buy. Overall it is, the meter works great and is almost as handy as the 381. The reason I give it 4 stars is because the Bluetooth is just terrible, and doesn't get you very far before it cuts out. I used to use the 381's removable display a lot, very handy for troubleshooting by yourself, I was hoping the Fluke Connect app could replace that function and make it an even trade off....it very much does not. If you have direct line of sight it will go about 30'-35', HOWEVER if you don't have L.O.S (like when it is in a closed cabinet as advertised, or when you are troubleshooting controls from elsewhere on a line) you loose connectivity at about 8-10'. That is rubbish, my ear buds stay connected 90' L.O.S and 45' through concrete walls and machinery....they should put a better BT version in this. Unfortunately it also doesn't come close to the 381's removable display distance either as I had no issues through obstacles with that either at 30-40' (assuming it was a lower frequency radio?). That is also separate from the functionality of the less than stellar fluke connect app itself.
So sadly, even though this is newer than the available Fluke 381, and has more measurement features...the wireless does not live up to the 381's practically, and makes me wish they would refresh that with stronger/better radios and more measurements.
Date published: 2020-08-17
Rated 1 out of 5 by Anonymous from Dont waste your money. This meter may work ok standalone. I bought it specifically for the fluke connect app. Doesnt work with my phone. No compatibility chart on web page. This thing is borderline paperweight.
Date published: 2020-07-28
Rated 1 out of 5 by Matt789 from very limited usefulness of the WiFi feature 1) for the WiFi feature to work, one has to log into a Fluke account, that is the meter does not connect to the phone app without a Fluke account.
2) the WiFi connection on the Fluke is flaky. When turning WiFi on, it should show up on the phone WiFi, but it does not. On the 376 FC, the WiFi symbol turns on, but no signal is detected by the phone or nearby PCs. At one point it had worked but that is no longer the case.
We don't use it very often and I was particularly excited about the WiFi feature. It could be nice if it were reliable.
Date published: 2020-06-17
Rated 2 out of 5 by EricM from Very disappointed with wild phantom readings. Fluke is a name in the testing industry that mostly goes unquestioned. I recently decided to upgrade my fluke meter after 7 years of service, That old meter still functions so well people ask me what it is and where to get one. With our company growing so should the quality and capibility of the equipment. I cannot express how disappointed i am with this new meter. The capability is there but the quality is disturbing, I have not even put this meter into service yet and in its current condition it will never seen in the field use. While not probing anything i am reciving false/ phntom readings between 0.5A to 15A DC. Do i have a faulty unit or have i just purchased o $500 tic tester?
Date published: 2020-06-09
Rated 5 out of 5 by Dylan1616 from Blown Away! This meter is the by far the greatest meter I have ever owned. I do HVAC and Electrical and it works great for both. 10/10 recommend to other techs out there!
Thanks fluke
Date published: 2019-10-11
Rated 4 out of 5 by Peter from Stability of Fluke Connect Mobile Software Both iOS & Android version of Fluke Connect are quite unstable for retreiving the data with time-stamp. Most of the cases, the time-stamp were incorrect. However it works fine when downloaded to the PC. This should be a program bug and would like to know how soon could Fluke solve it?
Date published: 2018-08-07
Rated 5 out of 5 by Shuvo from Word-class test and measurement Tools wow, wonderful clamp meter. Really accuracy is spot on. surely you can use this latest clamp meter with great feature. You can also find out clamp meter hare https://fluke.com.bd/
Date published: 2018-07-26
Rated 5 out of 5 by fire717 from Great Meter I just bought this meter and it works great, I do have a question I use the wire leads on the unit all the time and was wandering if fluke makes some kind of snap on lead holder or a rubber slip on holder to hold the leads on that you can buy as a accessory for a meter like this?
Date published: 2017-08-31