TITLE | USE WITH |
6003A | All |
The updating of embedded software should only be performed after given specific instructions to do so from Technical Support or a Fluke Calibration Authorized Service Center. If the update isn't performed properly, your product may be inoperable until it is. | |
Instructions to update by USB | |
Installation Put the CD into the computer, wait for autorun and select “Software installation” and “Uploader” or start direct “install\freeware\uploader”. Uninstall Uploader To remove the Uploader software from your system, you should run “uninstall” from “Programs” ("Start -> Programs -> Uploader -> Uninstall Uploader" from the Windows Start menu). Uploading Firmware 1. Connect the calibrator to the computer using an RS232 cable. 2. Select RS232 in the instrument menu as the active interface and set the baud rate to 9600 Bd. 3. Start the Uploader “Start->Program files->Uploader->Uploader.exe”. The following screen will appear: ![]() 4. Select computers port (COM1 … COM32) and the source file. The source file is a data file that contains the new firmware with the extension “.upl”. 5. Press “Connect”. The following screen will appear: ![]() 6. It is recommended to keep the transfer speed as-is and press “Upload” (in the case of an unsuccessful upload, reduce the transfer speed and try again). The following screen will appear: ![]() 7. Uploader automatically reloads all internal programs step by step. 8. After successful upload, the Uploader displays the following: ![]() Problems While Uploading New Firmware In the case that the upload does not finish properly (power supply disconnection, failed communication, etc.) the instrument will no longer contain internal software. Switch the instrument’s power supply off, wait approximately 10 seconds, and switch it on again. The instrument will display the message “Internal SW damaged!”. Repeat the procedure upload. The instrument is switched to RS232, 9600Bd mode automatically. | |
Updates Include: | |
Version 1.048 (2019 Oct. 25) Fix: Bug fixed that caused the GUI to lock up when too many characters were entered into the calibration password field. |
Découvrir d´autres marques Fluke
-
Produits
-
- Présenté
- Accessoires
- Infrastructure du bâtiment
-
Test électrique
- Multimètres numériques
- Testeurs de base
- Pinces multimètres
- Qualité du réseau électrique
- De mise à la terre
- Testeurs d'installations électriques
- Sécurité intrinsèque
- Analyseurs de batterie
- Controleurs d'isolement
- Oscilloscopes portables
- Instruments pour l’industrie solaire
- eMobility
- Testeurs sans fil
- Caméras thermiques et acoustiques
- Mesure de température
- Testeurs de câbles réseau
- Outils d´alignement
- Outils d’étalonnage
- Logiciel Fluke
-
- Apprendre
- Assistance
-
- 10 Produits
- 6 Apprendre
- 2 Assistance
- Produits
- 4 Présenté
- 2 Accessoires
- 4 Infrastructure du bâtiment
- 13 Test électrique
- 3 Caméras thermiques et acoustiques
- 2 Mesure de température
- 1 Testeurs de câbles réseau
- 1 Outils d´alignement
- 9 Outils d’étalonnage
- 2 Logiciel Fluke
- Infrastructure du bâtiment
- Outils CVC (HVAC)
- Test de la qualité de l’air intérieur
- Télémètres laser
- Niveaux laser
- Test électrique
- Multimètres numériques
- Testeurs de base
- Pinces multimètres
- Qualité du réseau électrique
- De mise à la terre
- Testeurs d'installations électriques
- Sécurité intrinsèque
- Analyseurs de batterie
- Controleurs d'isolement
- Oscilloscopes portables
- Instruments pour l’industrie solaire
- eMobility
- Testeurs sans fil
- Caméras thermiques et acoustiques
- Caméras thermiques
- Détection de fuite et de décharge partielle
- Hublots IR
- Outils d’étalonnage
- Calibrateurs de process
- Étalonnage électrique
- Étalonnage RF
- Équipements de test et d'acquisition de données
- Étalonnage de la température
- Étalonnage de l´humidité
- Étalonnage de la pression
- Étalonnage de débit
- Logiciel Fluke Calibration
- Apprendre
- 7 Centre de ressources Fluke
- Etudes de cas
- Séminaires et formation
- Salons professionnels
- Séminaires en ligne
- 8 Outils et calculateurs
- Centre de ressources Fluke
- Les fondamentaux
- Etalonnage
- Gestion de l'énergie
- Maintenance + monitoring
- Sécurité
- Réparation
- Tous les sujets
- Outils et calculateurs
- Calculateur de fuite d´air | ROI
- Calculateur de champ de visée
- ii-Series reporting tool
- PT100 calculator
- FCAL PT100 table generator
- Downtime cost calculator
- Convertisseur de tension du thermocouple en température
- Calcul par type de thermocouple
- Service clientèle
- Nous contacter
- Premium Care
- Services d'étalonnage
- Réparation
- Centres de réparation
- Qualité et accréditations
- Autorisation de renvoi du matériel
- MET/SUPPORT
- Ressources produits
- Base de connaissances
- Manuels
- Enregistrement de produit
- Notices de sécurité
- Télécharger les mises à jour logicielles
- Garanties
- Material safety data sheets (MSDS)