ScopeMeter®  Firmware Upgrade

• Several issues on CAN, FF and Profibus DP have been resolved (2x5C only)
• F2 is disabled in eye-pattern button bar when bus health is off (2x5C only)
• Fixed Dot-join status after leaving bushealth mode (2x5C only)
• Fixed Trigger status indication after leaving bushealth mode (2x5C only)
• No data banner no longer appears when wiring diagram is shown (2x5C only)
• Fixed recall function, not correctly recalling screen + data (V8.04)
• Fixed TrendPlot Save. UI only showed Screen + setting not Recording (V8.04)
• Fixed Trend storage (V8.02)
• Remote Control Fluke 190 Series improved (V7.06)
• Zoom in 2s/div timebase setting improved and micro symbol added in readings symbol table (V7.04)
• Improved screen update rate (V7.02)
• Deeper waveform memory up to 3K spectrum analysis using Fast Fourier Transformation (V7.00)
• Two new trigger modes (n-cycle and dual edge) (V7.00)
• Cursor limited automatic measurement (rms Watt etc between cursors) (V7.00)

Upgrading Version V7.0x, V8.00 or V8.02 to Version V8.04 - Instruments with version V7.01 to V8.02 are field upgradable free of charge.
v8.04 FlashTool Upgrade »

FlashTool Software requirements:

• Fluke 190C/2x5C Series Color ScopeMeter, with firmware V7.0 1V 8 .0 2 . (See Firmware Level Check above);
• A PC, running Windows XP or Vista, with a free RS-232 or USB port to perform the software installation;
• PM9080 or OC4USB (RevII) optically isolated serial interface cable (as included with the ScopeMeter 19xC/S model and with the SCC-190 kit) for data interconnection between the PC and the instrument

Upgrading earlier Versions - Instruments with firmware version V5.0x and V6.x cannot be upgraded to V8.04 in the field. These instruments require re-calibration after upgrading. Therefore these units must be returned to a Fluke Authorized Service Center. Contact your local service center and order a firmware upgrade and calibration according to PCN 4841. Note: For the firmware upgrade and calibration a nominal fee will be charged!

A firmware upgrade for ScopeMeter test tool 190B Series is available, major changes are:

• Remote Control improved (V7.06)
• Zoom in 2s/div timebase setting improved and micro symbol added in readings symbol table (V7.04)
• Improved screen update rate (V7.02)
• Deeper waveform memory up to 3K spectrum analysis using Fast Fourier Transformation (V7.00)
• Two new trigger modes (n-cycle and dual edge) (V7.00)
• Cursor limited automatic measurement (rms Watt etc between cursors) (V7.00)

Upgrading Version V7.00, V7.01, V7.02 or V7.04 to Version V7.06 - Instruments with version V7.00 to V7.04 are field upgradable free of charge.
v7.06 FlashTool Upgrade »

FlashTool Software requirements:

• Fluke 190 B Series ScopeMeter or 190B Series (Monochrome) ScopeMeter, with firmware V7.00 - V7.04. (See Firmware Level Check above);
• A PC, running Windows 95, 98, Me, 2000, NT 4.0, XP or Vista, with a free RS-232 or USB port to perform the software installation;
• PM9080 or OC4USB (RevII) optically isolated serial interface cable (as included with the ScopeMeter 19x B /S model and with the SCC-190 kit) for data interconnection between the PC and the instrument

Upgrading earlier Versions - Instruments with firmware version V5.0x and V6.x cannot be upgraded to V7.06 in the field. These instruments require re-calibration after upgrading. Therefore these units must be returned to a Fluke Authorized Service Center. Contact your local service center and order a firmware upgrade and calibration according to PCN 4841. Note: For the firmware upgrade and calibration a nominal fee will be charged!

A firmware upgrade for ScopeMeter test tool 190C Series is available, major changes are:

• Improved TrendPlot scaling
• Improved Voltage Readings stability
• When performing a TrendPlot of an Input A measurement, the probe attenuation factor of Input B was shown.
• If a meter TrendPlot is acquired in FlukeView 4.0, it can show a scaling error. This happens if a previously acquired TrendPlot had different range or probe attenuator settings.

Upgrading Version V5.03, V5.04 and V6.xx to Version V6.15 - Instruments with firmware version V5.03 – V6.14 are field upgradable free of charge.
v6.15 FlashTool Upgrade »

FlashTool Software requirements:

• Fluke 190C Series Color ScopeMeter, with firmware version V5.03 to V6.14. (See Firmware Level Check below);
• A PC, running Windows 98, Me, 2000, NT 4.0, XP or Vista, with a free RS-232 or USB port to perform the software installation;
• PM9080 or OC4USB (RevII) optically isolated serial interface cable (as included with the ScopeMeter 19xC/S model and with the SCC-190 kit) for data interconnection between the PC and the instrument

Firmware Level Check - Press USER and F3 [VERSION & CAL …] on your ScopeMeter to check its firmware version.

• Improved TrendPlot scaling
• Improved Voltage Readings stability
• When performing a TrendPlot of an Input A measurement, the probe attenuation factor of Input B was shown.
• If a meter TrendPlot is acquired in FlukeView 4.0, it can show a scaling error. This happens if a previously acquired TrendPlot had different range or probe attenuator settings.

Upgrading Version V6.00, V6.10, V6.11 and V6.12 to V6.13 - Instruments with firmware version V6.00 – V6.12 are field upgradable free of charge. 
v6.13 FlashTool Upgrade »

FlashTool Software requirements:

• Fluke 190 B Series ScopeMeter, with firmware version V 6.00 to V6.12 (See Firmware Level Check below);
• A PC, running Windows 98, Me, 2000, NT 4.0, XP or Vista, with a free RS-232 or USB port to perform the software installation;
• PM9080 or OC4USB (RevII) optically isolated serial interface cable (as included with the ScopeMeter 19x/S model and with the SCC-190 kit) for data interconnection between the PC and the instrument

Firmware Level Check - Press USER and F3 [VERSION & CAL …] on your ScopeMeter to check its firmware version.

• Measurement of total power (W) in Harmonics corrected (V3.03)
• Foundation Fieldbus limits H1 according IEC 61158 (V3.02)
• Improved task scheduler for Bushealth (V3.01)

Upgrading Version V3.00, V3.01,V3.02 or V3.03 to Version V3.04 - Instruments with firmware version V3.00, V3.01,V3.02 or V3.03 are field upgradeable free of charge.
v3.04 FlashTool Upgrade »

FlashTool Software requirements:

• Fluke 125 Series ScopeMeter, with firmware version V3.00, V3.01 or V3.02 (See Firmware Level Check below);
• A PC, running Windows 95, 98, Me, 2000, NT 4.0, XP or Vista, with a free RS-232 or USB port to perform the software installation;
• PM9080 or OC4USB (RevII) optically isolated serial interface cable (as included with the ScopeMeter 125/S model and with the SCC-120 kit) for data interconnection between the PC and the instrument

Firmware Level Check - Press USER OPTIONS and F3 [VERSION & CAL …] on your ScopeMeter to check its firmware version.

• Battery refresh time changed from 12 to 19 hours to reflect the real situation (V2.02)
• Postscript printing improved. (V2.01)
• A screen refresh is done after a 'send setup' action (V2.01)

Upgrading Version V2.00, V2.01 or V2.02  to Version V2.03 - Instruments with firmware version V2.0x  are field upgradable free of charge.
v2.03 FlashTool Upgrade »

• Fluke 123 Series ScopeMeter, with firmware version V2.00 to V2.02 (See Firmware Level Check below);
• A PC, running Windows 95, 98, Me, 2000, NT 4.0, XP or Vista, with a free RS-232 or USB port to perform the software installation;
• PM9080 or OC4USB (RevII) optically isolated serial interface cable (as included with the ScopeMeter 12x/S model and with the SCC-120 kit) for data interconnection between the PC and the instrument

Firmware Level Check - Press USER OPTIONS and F3 [VERSION & CAL …] on your ScopeMeter to check its firmware version.

Upgrading earlier Versions - Instruments with firmware version V1.0x cannot be upgraded to V2.03