Keeping your world up and running.
Home  |  Support  |  Software Downloads  |  ScopeMeters Software Downloads

Updates and Software Downloads for Fluke ScopeMeter® Test Tools


ScopeMeter® Test Tools Firmware Downloads »
FlukeView® for ScopeMeter® Test Tools »
FlukeView 2 for ScopeMeter® 120B Series Test Tools »

ScopeMeter® Test Tools Firmware Downloads


For Fluke 190 Series II, 2 and 4 Channel instruments

Firmware release V11.44 » 
Firmware Release V11.44 Readme »
  • Improved trigger delay handling for fastest timebase settings (scope mode)
  • Production related improvement

Firmware release V11.43
  • Fixed issue where some units could show unstable behavior for some channels, erroneous base line level and/or sometimes incorrect amplitude of waveform. This only applies to some units that have '2516' at the end of the Subversion information that is visible when selecting User key, F3=Version&Cal.
  • Fixed issue with channel setting replication so that auto/manual ranging is now copied as well. Channel replication is selected by push and hold channel key and push another channel key.
  • Fixed icellSpacingssue that could lead to disappearing channel ground indication on left of display when waveform is moved to bottom of screen.

Firmware version V11.42

The firmware release V11.42 has fixed the following issue:

  • Production related improvements to support new component

Firmware version V11.41

The firmware release V11.41 has fixed the following issues:

  • Improved speed of acquisition for replay and pass/fail testing
  • Fixed issues with pass/fail testing and replay playback
  • Fixed issues with spectrum display
  • Fixed issue with BWL indication in meter mode
  • Fixed issue with rounding frequency results

Firmware version V11.40

The release V11.40 update has fixed the following issues:

  • Improved speed of acquisition for replay and pass/fail testing
  • Fixed issues with pass/fail testing and replay playback
  • Fixed issues with spectrum display
  • Fixed issue with rounding frequency results
  • Fixed issue with BWL indication in meter mode

Firmware version V11.30

For 190 Series II, 2 and 4 Channel ScopeMeter test tools with version V09.00 onwards. The release V11.30 update has fixed the following issues (link to file download V11.30):

  • Fixed potential startup problem related to no traces on screen, or in the 4 Channel version no accessible C&D channels (*)
  • Fixed issues in storing and reading of ScopeRecord and Trendplot data as .CSV to USB
  • Fixed issue when ScopeMeter was turned off in TrendPlot mode with cursors on (*)

    Before the release of V11.30 this issue could be solved by following the below given steps:


    • Switch off the ScopeMeter test tool
    • Disconnect the power supply

    Wait for 5 minutes before continuing with the following steps:


    • Connect the power supply
    • Switch on the ScopeMeter test tool
    • Insert the battery pack (The battery will be charged)

Firmware version V11.20

For 190 Series II, 2 and 4 Channel ScopeMeter test tools with version V09.00 onwards. The release V11.40 update has fixed the following issues:

  • Ability to open saved waveforms of V10.0 or later
  • Fixed .BMP format problem when copying images from INT to USB
  • Prevent locking of instrument when data is copied from USB stick and no stick is present

Firmware version V11.10

For 190 Series II, 2 and 4 Channel ScopeMeter test tools with version V09.00, V10.4X or V11.0. The release V11.10 update addresses bug fixing and the possibility to store waveforms from within the ScopeMeter test tool on to a USB-stick as a CSV-file, then open this using FlukeView or a spreadsheet program.

Firmware version V11.10

Fluke 190 Series II, 4 Channel Instruments with V10.40 Firmware, Safety Notice and Recall

For 190 Series II, 4 Channel ScopeMeter test tools with version V10.40 firmware has a measurement reading decimal point display problem that requires a firmware update to V10.41 or higher to avoid a potential user safety risk.


Fluke ScopeMeter® 120B Series

Firmware release V1.10.01 »


For Fluke 123B, 124B and 125B ScopeMeter Test Tools this software update has the following improvements:
  • Fixed issue in Fluke 125B Power Harmonics where VA, var and pf readings were not displayed
  • Fixed issue in Fluke 125B Power Harmonics where K Factor readings were incorrect
  • Fixed issue in Scope Recorder where Channel B attenuation factor was incorrect after recording was stopped
  • Fixed issue in Fluke 125B BusHealth mode where the eye pattern display was incorrect
  • Improved functionality of AutoHold so that it is not turned off after selecting F4 = Done

To update firmware:
  1. Download the firmware file
  2. Copy the firmware file to a Micro SD card
  3. Turn off the unit and remove all probes, test leads, and accessories before opening the battery door
  4. Open the battery door compartment using screwdriver
  5. Insert Micro SD card into the slot
  6. Power on the unit and press the MENU key
  7. Select USER OPTIONS
  8. Select Firmware Upgrade
  9. Follow the instructions on the screen


Fluke 190 Series and 2X5C Series Option and language configuration fix

European versions of Fluke 190C series with serial number 1152xxxx to 1170xxxx tool to fix Polish, Czech and Russian user language support. Please contact the Fluke service department for firmware updates on this product.
Fluke 2X5C with Bus health test option, tool to fix option configuration and Polish, Czech and Russian European language support. Please contact the Fluke service department for firmware updates on this product.

Fluke 190C Series or 2x5C Series

Firmware V8.04 »
For Version V7.0x, V8.00 or V8.02
Firmware V6.15 »
For versions V6.14, V6.13, V6.12, V6.11, V6.10, V6.00, V5.04, V5.03 (Note: an upgrade to V7.06 requires re-calibration, contact Fluke service center)

Fluke 190B Series »

Firmware V7.06 »
For versions V7.00, V7.01, V7.02 or V7.04
Firmware V6.13 »
For Versions V6.00, V6.10, V6.11 and V6.12 to V6.13

Fluke 190 Series (non B/C)

Contact your local Fluke service center

Fluke 120 Series »

Fluke 125 Firmware upgrade V3.04 »
For versions V3.03, V3.02, V3.01, V3.00
Fluke 123, 124 Firmware upgrade V2.03 »
For versions V2.02, V2.01, V2.00
Fluke 123 Firmware upgrade V1.08 »
For versions V1.04, V1.03, V1.02, V1.00

FlukeView® for ScopeMeter® Test Tools

Upgrade to FlukeView version 5.4 (.exe) »

Application software for download, analysis and reporting.
Used with Fluke 190 Series II, Fluke 120 Series, Fluke 19xB/C Series and Fluke 2x5C Series.

This is a demo version with limited functionality. The full version can be obtained with activation key that is available as an option.

Release notes:
Relative to the previous version the following changes have been implemented:

  • Support for increased amount of memory locations in newer Fluke-104 and Fluke-204 products.
  • Corrected cursor values of TrendPlot for Fluke 12x.
  • Corrected error when zooming in ScopeRecord.
  • Corrected downloading of full single shot ScopeRecord.
  • Corrected downloading of setups for Fluke 190-II.

FlukeView 2 for ScopeMeter® Test Tools

FlukeView-2 for ScopeMeter® Test Tools version 1.0 (.exe) »

Application software for download, analysis and reporting.
Used with Fluke 120B Series.

This is a demo version with limited functionality. The full version can be obtained with activation key that is available as an option.


Home   |   Site Map   |   Fluke Corporation   |   Safety Notices
Privacy Statement   |   Terms of Use  |   Terms and Conditions of Sale
© 1995 - 2018 Fluke Corporation